@@ -18,20 +18,5 @@
EXTRA_DIST = \
sample-plugins \
sample-config-files \
- sample-windows \
sample-keys \
sample-scripts
-
-if WIN32
-sample_DATA = \
- client.ovpn \
- server.ovpn \
- sample-windows/sample.ovpn
-
-client.ovpn: sample-config-files/client.conf
- -rm -f client.ovpn
- cp "$(srcdir)/sample-config-files/client.conf" client.ovpn
-server.ovpn: sample-config-files/server.conf
- -rm -f server.ovpn
- cp "$(srcdir)/sample-config-files/server.conf" server.ovpn
-endif
deleted file mode 100755
@@ -1,102 +0,0 @@
-# Edit this file, and save to a .ovpn extension
-# so that OpenVPN will activate it when run
-# as a service.
-
-# Change 'myremote' to be your remote host,
-# or comment out to enter a listening
-# server mode.
-remote myremote
-
-# Uncomment this line to use a different
-# port number than the default of 1194.
-; port 1194
-
-# Choose one of three protocols supported by
-# OpenVPN. If left commented out, defaults
-# to udp.
-; proto [tcp-server | tcp-client | udp]
-
-# You must specify one of two possible network
-# protocols, 'dev tap' or 'dev tun' to be used
-# on both sides of the connection. 'tap' creates
-# a VPN using the ethernet protocol while 'tun'
-# uses the IP protocol. You must use 'tap'
-# if you are ethernet bridging or want to route
-# broadcasts. 'tun' is somewhat more efficient
-# but requires configuration of client software
-# to not depend on broadcasts. Some platforms
-# such as Solaris, OpenBSD, and Mac OS X only
-# support 'tun' interfaces, so if you are
-# connecting to such a platform, you must also
-# use a 'tun' interface on the Windows side.
-
-# Enable 'dev tap' or 'dev tun' but not both!
-dev tap
-
-# This is a 'dev tap' ifconfig that creates
-# a virtual ethernet subnet.
-# 10.3.0.1 is the local VPN IP address
-# and 255.255.255.0 is the VPN subnet.
-# Only define this option for 'dev tap'.
-ifconfig 10.3.0.1 255.255.255.0
-
-# This is a 'dev tun' ifconfig that creates
-# a point-to-point IP link.
-# 10.3.0.1 is the local VPN IP address and
-# 10.3.0.2 is the remote VPN IP address.
-# Only define this option for 'dev tun'.
-# Make sure to include the "tun-mtu" option
-# on the remote machine, but swap the order
-# of the ifconfig addresses.
-;tun-mtu 1500
-;ifconfig 10.3.0.1 10.3.0.2
-
-# If you have fragmentation issues or misconfigured
-# routers in the path which block Path MTU discovery,
-# lower the TCP MSS and internally fragment non-TCP
-# protocols.
-;fragment 1300
-;mssfix
-
-# If you have set up more than one TAP-Win32 adapter
-# on your system, you must refer to it by name.
-;dev-node my-tap
-
-# You can generate a static OpenVPN key
-# by selecting the Generate Key option
-# in the start menu.
-#
-# You can also generate key.txt manually
-# with the following command:
-# openvpn --genkey secret key.txt
-#
-# key must match on both ends of the connection,
-# so you should generate it on one machine and
-# copy it to the other over a secure medium.
-# Place key.txt in the same directory as this
-# config file.
-secret key.txt
-
-# Uncomment this section for a more reliable
-# detection when a system loses its connection.
-# For example, dial-ups or laptops that travel
-# to other locations.
-#
-# If this section is enabled and "myremote"
-# above is a dynamic DNS name (i.e. dyndns.org),
-# OpenVPN will dynamically "follow" the IP
-# address of "myremote" if it changes.
-; ping-restart 60
-; ping-timer-rem
-; persist-tun
-; resolv-retry 86400
-
-# keep-alive ping
-ping 10
-
-# enable LZO compression
-comp-lzo
-
-# moderate verbosity
-verb 4
-mute 10